Ask question

Ask question

All categories

2 years ago

4

Design an algorithm that, when given an arrangement of the digits 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, rearranges the digits so that th

e new arrangement represents the next larger value that can be represented by these digits (or reports that no such rearrangement exists if no rearrangement produces a larger value). Thus 5647382901 would produce 5647382910.

1 answer:

Nuetrik [128]2 years ago

8 0

Answer:

Attached below

Explanation:

You might be interested in

The electrical energy used by an air conditioner for 2 minutes is 180 kJ. Calculate the power of this air conditioner in the fol

ELEN [110]

Answer:

I hope it is correct.....

5 0

2 years ago

What is the physical significance of the Reynolds number?. How is defined for external flow over a plate of length L.

yanalaym [24]

Answer:

$Re=\dfrac{\rho\ v\ l}{\mu }$

Explanation:

Reynolds number:

Reynolds number describe the type of flow.If Reynolds number is too high then flow is called turbulent flow and Reynolds is low then flow is called laminar flow .

Reynolds number is a dimensionless number.Reynolds number given is the ratio of inertia force to the viscous force.

$Re=\dfrac{F_i}{F_v}$

For plate can be given as

$Re=\dfrac{\rho\ v\ l}{\mu }$

Where ρ is the density of fluid , v is the average velocity of fluid and μ is the dynamic viscosity of fluid.

Flow on plate is a external flow .The values of Reynolds number for different flow given as

$Reynolds\ number\is \ >\ 5 \times 10 ^5\ then\ flow\ will\ be\ turbulent.$

$Reynolds\ number\is \$

7 0

2 years ago

Instructions given by traffic police or construction flaggers _____. A. Are sometimes important to follow B. Are usually not imp

Anestetic [448]

Answer:

D. Overrule any other laws and traffic control devices.

Explanation:

Laws and traffic control devices are undoubtedly compulsory to be followed at every point in time to control traffic and other related situations. However, there are cases when certain instructions overrule these laws and traffic control devices. For example, when a traffic police is giving instructions, and though the traffic control devices too (such as traffic lights) are displaying their own preset lights to control some traffic, the instructions from the traffic police take more priority. This is because at that point in time, the instructions from the traffic control devices might not be just applicable or sufficient.

Also, in the case of instructions given by construction flaggers, these instructions have priority over those from controlling devices. This is because during construction traffic controls are redirected from the norms. Therefore, the flaggers such be given more importance.

6 0

2 years ago

A woodcutter wishes to cause the tree trunk to fall uphill, even though the trunk is leaning downhill. With the aid of the winch

Sedbober [7]

Answer:

The correct answer will be "400.4 N". The further explanation is given below.

Explanation:

The given values are:

Mass of truck,

m = 600 kg

g = 9.8 m/s²

On equating torques at the point O,

⇒ $T\times Cos(10+5)\times (1.3+4)=mg\times Sin(5)\times 4$

So that,

On putting the values, we get

⇒ $T\times Cos(15^{\circ})\times 5.3=600\times 9.8\times Sin(5^{\circ})\times 4$

⇒ $T=400.4 \ N$

8 0

2 years ago

Superheated steam at an average temperature 200 C is transported through a steel pipe (k=50 W/mK, D_0=8.0 cm,D_i=6.0 cm,and L=20

Zarrin [17]

The total amount of daily heat transfer is 1382.38 M w.

The temperature on the outside surface of the gypsum plaster insulation is 17.96 ° C.

<u>Explanation:</u>

Given data,

$T_{\infty}$ = 10° C

$h_{0}$ = 250 w/ $m^{2}$ k

Pipe length = 20 m

Inner diameter $d_{1}$ = 6 cm, $r_{1}$ = 3 cm

Outer diameter $d_{2}$ = 8 cm, $r_{2}$ = 4 cm

The thickness of insulation is 4 cm.

$r_{3}$ = $r_{2}$ + 4

= 4+4

$r_{3}$ = 8 cm

$h_{0}$ is the heat transfer coefficient of convection inside, $h_{i}$ is the heat transfer coefficient of convection outside.

The heat transfer rate between ambient and steam is

$q=\frac{T_{S}-T_{\infty}}{\frac{1}{h_{i}\left(2 \pi r_{1} L\right)}+\frac{\ln \left(r_{2} / r_{1}\right)}{2 \pi K_{1} L}+\frac{\ln \left(r_{3}/ r_{2}\right)}{2 \pi K_{2} L}+\frac{1}{h_{0}\left(2 \pi r_{3} L\right)}}$ watt

= $\begin{aligned}&\frac{1}{800(2 \pi x \cdot 03 \times 20)}\++\frac{\ln (4 / 3)}{2 \pi \times 50 \times 20}+\frac{\ln (8 / 4)}{2 \pi \times 0.5 \times 20}+\frac{1}{200(2 \pi x \cdot 08 \times 20)}\end{aligned}$ watt

= $\frac{190}{0.0003317+0.0000458+0.0110+0.0004976}$ watt

q = 15999.86 watt

The total amount of daily heat transfer = 15999.86 × 86400

= 1382.387904 watt

= 1382.38 M w

The total amount of daily heat transfer is 1382.38 M w.

b) The temperature on the outside surface of the gypsum plaster insulation.

q = $\frac{T_{3}-T_{\infty}}{\frac{1}{\ln \left(2 \pi \ r_{3} L\right)}}$

15999.86 $=\frac{\frac{1}{T_3}-10}{\frac{1}{200(2 \pi . 08 \times 20)}}$

$T_{3}$ - 10 = 7.96

$T_{3}$ = 17.96 ° C.

4 0

2 years ago