Ask question

Ask question

All categories

2 years ago

6

You are driving in an area where rain has pooled on the road, and you have driven through water that was several inches deep. Yo

u should

1 answer:

pantera1 [17]2 years ago

3 0

Answer:

drive a little slower

Explanation:

you do not want to hydroplane and do 360s down the road at 80MPH

You might be interested in

A platinum resistance temperature sensor has a resistance of 120 Ω at 0℃ and forms one arm of a Wheatstone bridge. At this tempe

oksian1 [2.3K]

Answer : 9.36ohms/ temperature

Explanation:

Expression for the variation of resistance of platinum with temperature

Rt= Ro(1+*t)

Rt= resistance @ t°C

Ro= resistance @ 0°C

*= temperature coefficient of resistance

Calculate the change in resistance by putting 120ohms for Ro,

0.0039/K for *

20°C for t

Using this formula:

Rt = Ro(1+*t)

Rt- Ro = Ro*t

= (120ohms)(0.0039/K)(20°C)

= 9.36ohms/K

8 0

2 years ago

The closed tank of a fire engine is partly filled with water, the air space above being under pressure. A 6 cm bore connected to

skelet666 [1.2K]

Answer:

The air pressure in the tank is 53.9 $kN/m^{2}$

Solution:

As per the question:

Discharge rate, Q = 20 litres/ sec = $0.02\ m^{3}/s$

(Since, 1 litre = $10^{-3} m^{3}$ )

Diameter of the bore, d = 6 cm = 0.06 m

Head loss due to friction, $H_{loss} = 45 cm = 0.45\ m$

Height, $h_{roof} = 2.5\ m$

Now,

The velocity in the bore is given by:

$v = \frac{Q}{\pi (\frac{d}{2})^{2}}$

$v = \frac{0.02}{\pi (\frac{0.06}{2})^{2}} = 7.07\ m/s$

Now, using Bernoulli's eqn:

$\frac{P}{\rho g} + \frac{v^{2}}{2g} + h = k$ (1)

The velocity head is given by:

$\frac{v_{roof}^{2}}{2g} = \frac{7.07^{2}}{2\times 9.8} = 2.553$

Now, by using energy conservation on the surface of water on the roof and that in the tank :

$\frac{P_{tank}}{\rho g} + \frac{v_{tank}^{2}}{2g} + h_{tank} = \frac{P_{roof}}{\rho g} + \frac{v_{tank}^{2}}{2g} + h_{roof} + H_{loss}$

$\frac{P_{tank}}{\rho g} + 0 + 0 = \0 + 2.553 + 2.5 + 0.45$

$P_{tank} = 5.5\times \rho \times g$

$P_{tank} = 5.5\times 1\times 9.8 = 53.9\ kN/m^{2}$

4 0

2 years ago

What properties should the head of a carpenter’s hammer possess? How would you manufacture a hammer head?

BabaBlast [244]

Properties of Carpenter's hammer possess

Explanation:

1.The head of a carpenter's hammer should possess the impact resistance, so that the chips do not peel off the striking face while working.

2.The hammer head should also be very hard, so that it does not deform while driving or eradicate any nails in wood.

3.Carpenter's hammer is used to impact smaller areas of an object.It can drive nails in the wood,can crush the rock and shape the metal.It is not suitable for heavy work.

How hammer head is manufactured :

1.Hammer head is produced by metal forging process.

2.In this process metal is heated and this molten metal is placed in the cavities said to be dies.

3.One die is fixed and another die is movable.Ram forces the two dies under the forces which gives the metal desired shape.

4.The third process is repeated for several times.

5 0

2 years ago

Laminar flow normally persists on a smooth flat plate until a critical Reynolds number value is reached. However, the flow can b

grandymaker [24]

Answer:

At L = 0.1 m

h⁻_lam = 11.004K W/m^1.5

h⁻_turb = 7.8848K W/m^1.8

At L = 1 m

h⁻_lam = 3.48K W/m^1.5

h⁻_turb = 4.975K W/m^1.8

Explanation:

Given that;

h_lam(x)= 1.74 W/m^1.5. Kx^-0.5

h_turb(x)= 3.98 W/m^1.8 Kx^-0.2

conditions for plates of length L = 0.1 m and 1 m

Now

Average heat transfer coefficient is expressed as;

h⁻ = 1/L ₀∫^L hxdx

so for Laminar flow

h_lam(x)= 1.74 . Kx^-0.5 W/m^1.5

from the expression

h⁻_lam = 1/L ₀∫^L 1.74 . Kx^-0.5 dx

= 1.74k / L { [x^(-0.5+1)] / [-0.5 + 1 ]}₀^L

= 1.74k/L = [ (x^0.5)/0.5)]⁰^L

= 1.74K × L^0.5 / L × 0.5

h⁻_lam= 3.48KL^-0.5

For turbulent flow

h_turb(x)= 3.98. Kx^-0.2 W/m^1.8

form the expression

1/L ₀∫^L 3.98 . Kx^-0.2 dx

= 3.98k / L { [x^(-0.2+1)] / [-0.2 + 1 ]}₀^L

= (3.98K/L) × (L^0.8 / 0.8)

h⁻_turb = 4.975KL^-0.2

Now at L = 0.1 m

h⁻_lam = 3.48KL^-0.5 = 3.48K(0.1)^-0.5 W/m^1.5

h⁻_lam = 11.004K W/m^1.5

h⁻_turb = 4.975KL^-0.2 = 4.975K(0.1)^-0.2

h⁻_turb = 7.8848K W/m^1.8

At L = 1 m

h⁻_lam = 3.48KL^-0.5 = 3.48K(1)^-0.5 W/m^1.5

h⁻_lam = 3.48K W/m^1.5

h⁻_turb = 4.975KL^-0.2 = 4.975K(1)^-0.2

h⁻_turb = 4.975K W/m^1.8

Therefore

At L = 0.1 m

h⁻_lam = 11.004K W/m^1.5

h⁻_turb = 7.8848K W/m^1.8

At L = 1 m

h⁻_lam = 3.48K W/m^1.5

h⁻_turb = 4.975K W/m^1.8

3 0

2 years ago

Dust, dirt, or metal chips can pose a potential ____ injury risk in a shop.

pantera1 [17]

Answer:

Eye.

Explanation:

Dust, dirt, and metal chips are most unpleasant to get in your eyes. Just experience it and you'll know what I mean.

;)

3 0

2 years ago