answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
mixas84 [53]
2 years ago
6

A square loop of wire surrounds a solenoid. The side of the square is 0.1 m, while the radius of the solenoid is 0.025 m. The sq

uare loop has a resistance of 30 ohm . The solenoid has 500 turns and is 0.3 m long. The current in the solenoid is increasing at a constant rate of 0.7 A/s. What is the magnitude of the current flowing in the square loop?
Engineering
1 answer:
Semmy [17]2 years ago
6 0

Answer:

I=9.6×e^{-8}  A

Explanation:

The magnetic field inside the solenoid.

B=I*500*muy0/0.3=2.1×e ^-3×I.

so the total flux go through the square loop.

B×π×r^2=I×2.1×e^-3π×0.025^2

=4.11×e^-6×I

we have that

(flux)'= -U

so differentiating flux we get

so the inducted emf in the loop.

U=4.11×e^{-6}×dI/dt=4.11×e^-6×0.7=2.9×e^-6 (V)

so, I=2.9×e^{-6}÷30

I=9.6×e^{-8}  A

You might be interested in
A binary star system consists of two stars of masses m1m1m_1 and m2m2m_2. The stars, which gravitationally attract each other, r
d1i1m1o1n [39]

Answer:

          a_c_2=\dfrac{a_c_1\times m_1}{m_2}

Explanation:

The question is: <em>Find the magnitude of the centripetal acceleration of the star with mass m₂</em>

The <em>centripetal acceleration</em> is the quotient of the centripetal force and the mass.

                a_c=\dfrac{F_c}{m}

Thus, you can write the equations for each star:

     

       a_c_1=\dfrac{F_c_1}{m_1}

       a_c_2=\dfrac{F_c_2}{m_2}

As per Newton's third law, the centripetal forces are equal in magnitude. Then:

       a_c_1\times m_1=a_c_2\times m_2

Now you can clear a_c_2:

          a_c_2=\dfrac{a_c_1\times m_1}{m_2}

6 0
2 years ago
The rectangular frame is composed of four perimeter two-force members and two cables AC and BD which are incapable of supporting
Rama09 [41]

Answer:

Your question is lacking some information attached is the missing part and the solution

A) AB = AD = BD = 0, BC = LC

    AC = \frac{5L}{3}T, CD = \frac{4L}{3} C

B) AB = AD = BC = BD = 0

   AC = \frac{5L}{3} T, CD = \frac{4L}{3} C

Explanation:

A) Forces in all members due to the load L in position A

assuming that BD goes slack from an inspection of Joint B

AB = 0 and BC = LC from Joint D, AD = 0 and CD = 4L/3 C

B) steps to arrive to the answer is attached below

AB = AD = BC = BD = 0

AC = \frac{5L}{3} T,  CD = \frac{4L}{3}C

7 0
2 years ago
The extruder head in a fused- deposition modeling setup has a diameter of 1.25 mm (0.05 in) and produces layers that are 0.25mm
Angelina_Jolie [31]

Answer:

The time taken will be "1 hour 51 min". The further explanation is given below.

Explanation:

The given values are:

Number of required layers:

= \frac{38}{0.25}

= 152 \ layers

Diameter (d):

= 1.25 mm

Velocity (v):

= 40 mm/s

Now,

The area of one layer will be:

= 38\times 38 \ mm^2

= 1444 \ mm^2

The area covered every \second will be:

= d\times v

= 1.25\times 40

= 50 \ mm^2

The time required to deposit one layer will be:

= \frac{1444}{50}

= 28.88 \ sec

The time required for one layer will be:

= 15 \ sec

∴ Total times required for one layer will be:

= 15+28.88

= 43.88 \ sec

So,

Number of layers = 152

Therefore,

Total time will be:

= 152\times 43.88

= 6669.76 \ sec

= 1 \ hour \ 51 \ min

6 0
2 years ago
When should you exercise extreme caution around power lines?
Elis [28]

<em>You should take note and exercise extreme precautions when you are near power lines and consider the following: </em>

<em> </em>

<em>1. Make sure that you have a good distance away from the lines. The minimum distance you can get is 10 feet away from the lines. Be cautious as well when you see broken lines as they could still harm you and electrified you. </em>

<em>2. Do not make ladders, equipments and things around you touch the power lines as it may harm you as well. </em>

<em>3. Clear everything and ensure that no things are near you before you lift your hands and other tools.</em>

6 0
2 years ago
As the porosity of a refractory ceramic brick increases:
ivolga24 [154]

Answer:

A) strength decreases, chemical resistance decreases, and thermal insulation increases

Explanation:

Strength always decreases, chemical resistence decreases, and thermal condictivity must be reduced therefore themal insulation must increase.

7 0
2 years ago
Other questions:
  • A_____ transducer is a device that can convert an electronic controller output signal into a standard pneumatic output. A. pneum
    13·1 answer
  • Compute the mass fractions of α ferrite and cementite in pearlite. Assume T=726⁢ C∘.
    15·1 answer
  • Define a) Principal Plane b) Principal Stress c) anelasticity d) yield point e) ultimate tensile stress f) hardness g) toughness
    5·1 answer
  • The four-wheel-drive all-terrain vehicle has a mass of 320 kg with center of mass G2. The driver has a mass of 82 kg with center
    15·1 answer
  • A 0.9% solution of NaCl is considered isotonic to mammalian cells. what molar concentration is this?
    10·1 answer
  • A three-story school has interior column bays that are spaced 25 ft apart in both directions. If the loading on the flat roof is
    7·1 answer
  • The function below takes a single string parameter: input_string. If the input contains the lowercase letter z, return the strin
    15·1 answer
  • In this module you learned about searching, sorting and algorithms in C++ and how to implement these elements in your C++ progra
    6·1 answer
  • Benzene vapor at 480°C is cooled and converted to a liquid at 25°C in a continuous condenser. The condensate is drained into 1.7
    15·1 answer
  • What are practical considerations you might encounter when you increase the moment of inertia (I) while keeping the cross-sectio
    13·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!